BROTHER DCP-7010 TONER CARTRIDGES 5PACK

The lifespan of the toner cartridge installed in your Brother DCP-7010 is approx. 2,500 pages. You can extend the useful life of the installed toner cartridge by selecting [Ecology] – [Toner Save]. The installed toner cartridge should be replaced if any of the listed indications persists.

 

·         The message [No Cartridge] is displayed

 

·         The message [Toner Life End] is displayed

 

·         The message [Toner Low] is displayed

 

·         Insufficient toner density

 

·         Gray background

 

·         Toner stains down the page

 

·         White vertical lines

In the first step of the replacement procedure, you must open the front cover of your Brother DCP-7010, and then remove the drum unit and toner cartridge assembly. After that, you must press the lock release button, and then remove the exhausted toner cartridge from the drum unit. Now, you must take the new toner cartridge out of the aluminum bag, and then shake it several times from side to side. In the next step of the replacement procedure, you must remove the protective cover from the new toner cartridge, and then install the cartridge into the drum unit. Once the new toner cartridge is installed, you must clean the primary corona wire, and then reinstall the drum unit and toner cartridge assembly. Finally, you must close the front cover of your Brother DCP-7010. 

In the initial step of the replacement procedure, you must make sure that the Brother DCP-7010 is switched off, and then open the ADF unit. After that, you must open the scanner unit, and then remove the taptite screw. Now, you must remove the ADF FG harness and the FB FG harness, and then unplug the two ADF connectors from the main PCB. In the next step of the replacement procedure, you must unplug the two connectors of the scanner unit from the main PCB, and then close the ADF unit and the scanner unit. After that, you must detach the ADF cover by removing the two pins, and then release the two hooks of the pressure roller assembly. Now, you must remove the pressure roller assembly, and then detach the LF springs from the ADF cover. Once the LF springs are removed, you must remove the two rollers from the pressure roller shaft, and then open the ADF unit. Next, you must detach the gear cover from the ADF unit by releasing the hook, and then close the ADF unit. After that, you must remove the bushing and the roller shaft assembly from the ADF unit, and then remove the four taptite screws. In the next step, you must remove the upper document chute by releasing the three hooks, and then remove the separation rubber assembly from the upper chute. Once you have removed the separation rubber assembly, you must detach the separation rubber from the ADF plate spring, and then remove the two screws from the lower document chute. Next, you must remove the lower document chute by releasing the two hooks, and then remove the ejection roller assembly by releasing its hook from the ADF unit. After that, you must remove the ejections rollers from the pressure shaft, and then remove the ADF unit ejection spring. Once the ejection spring is detached, you must remove the following components:

·         Resin bearing

·         LF roller assembly

·         Ejection roller assembly (lower chute)

·         Ejection roller bearing (lower chute)

·         Drive frame assembly (lower chute)

·         ADF motor

·         ADF motor harness

·         Rear actuator (lower chute)

·         Front actuator (lower chute)

·         ADF sensor PCB

·         ADF sensor harness assembly

·         Document hold

·         Document spring

·         Document cover assembly

·         Pressure roller assembly

·         Hinge arm

Once all of the listed components are removed, you must detach the ADF unit from your Brother DCP-7010, and then unpack the replacement component. Finally, you must install the new ADF unit by executing the current procedure in reverse order.

Initially, you must make sure that your Brother DCP-7010 is switched off, and then remove the four taptite screws from the scanner unit. After that, you must release the four hooks, and then unplug the control panel connector from the PCB assembly. Now, you must detach the control panel from the scanner unit by releasing the three hooks, and then detach the LCD harness from the PCB of the control panel. In the next step of the replacement procedure, you must remove the control panel PCB from the control panel cover by releasing the three hooks, and then remove the rubber keyboard. Next, you must remove the backlight guide by releasing the two hooks, and then remove the diffusion film. Once the diffusion film has been removed, you must remove the LCD by releasing the two hooks, and then unpack the new control panel. Finally, you must install the new control panel by executing the current procedure in reverse order.

You must start the replacement procedure by switching your Brother DCP-7010 off. After that, you must disconnect the harness connectors of the heater and the thermistor, and then remove the two screws that fix the fuser assembly unit into place. Now, you must remove the fuser assembly unit from the Brother DCP-7010, and then remove the PR springs. In the next step of the replacement procedure, you must detach the pressure roller assembly from the fuser frame, and then remove the PR arm assemblies. Once the arm assemblies are removed, you must remove the PR bush from the pressure roller, and then remove the four separate claw assemblies by releasing the hooks from the springs. Next, you must remove the two screws that secure the exhausted heat roller into place, and then remove the exhausted component from the fuser assembly unit. Finally, you must unpack the new fuser heat roller, and then install it by executing the current procedure in reverse order.

In the first step of the replacement procedure, you must make sure that your Brother DCP-7010 is switched off, and then unplug the power cord. After that, you must remove the insulation sheet of the HVPS, and then remove the screws securing the gear plate calking assembly. Now, you must remove the gear plate calking assembly, and then remove the three fixing screws of the main motor assembly. Finally, you must remove the main motor assembly from the Brother DCP-7010, and then install the replacement component by executing the current procedure in reverse order.

In the first step of the replacement procedure, you must switch the Brother DCP-7010 off, and then unplug the power cord. After that, you must disconnect all thirteen connectors from the Main PCB, and then remove the five cup taptite screws. Now, you must remove the FG harness assembly, and then remove the two flat taptite screws. In the next step of the replacement procedure, you must remove the Main PCB from the printer frame, and then unpack the replacement component. Finally, you must install the new Main PCB by executing the current procedure in reverse order.

In the first step of the replacement procedure, you must switch your Brother DCP-7010 off, and then unplug the power cord. After that, you must unplug the speaker connector from the main PCB, and then remove the speaker cover by releasing the three hooks. Now, you must remove the speaker hold spring by releasing its hook, and then remove the speaker assembly. Finally, you must unpack the new speaker, and then install it by executing the current procedure in reverse order.